Clinical dental equipment is an essential tool for dentists, can be roughly divided into comprehensive treatment chair. Medical burs, dental handpiece, root canal measuring instrument, curing light, scaler, teeth whitening light, polished suits
2013年9月5日星期四
teeth invisible braces
Teeth invisible braces advantages:
1, convenient: You can pick their own wear, does not affect the social, eating, exercise and so on. While reducing the number of referral, saving you valuable time.
2 Clean: oral hygiene easier to maintain, do not worry gingivitis, tooth demineralization, discoloration and other issues.
3, convenient: Short and effective course of treatment, the general treatment can be completed around September to dental drill December. Traditional methods of treatment time of about 8 hours, invisible orthodontics only 3 hours.
4, appearance: almost completely invisible. You will notice it in someone else to complete orthodontics, solves many patients straightening teeth appearance concerns.
5 Comfort: Since there is no traditional sense of the bracket, steel and other orthodontic appliance correction process is no longer suffering. On periodontal tissue irritation and discomfort minimum.
2013年9月4日星期三
dental machine status abroad
We developed countries tableting machine with compression technology gap is widening, high yield, airtight, modular, automated, large-scale and advanced
Detection technology is the most important foreign tableting machine technology development direction. Advanced tableting machine base in Europe, such as Germany FETTE, KORSCH, UK MANESTY, Billy
When COURTOY, USA STOKES so on. High degree of automation of its products, in compliance with FDA requirements and 21CFRPART11 requirements.
(1) high speed, dental tools high yield. High speed and high output was tableting machine manufacturers over the years has always been the goal, the main tableting machine manufacturers already have hourly output
Reach 1 million tableting machine. If Manestry produced Xpress700 type tableting machine yield amounted to 1,000,000; Korsch XL800 type produced by tableting machine
Maximum output reached 1.02 million / h; Courtoy produced ModulD type tableting machine maximum output reached 1.07 million / h; Fette 4090i produced the highest type tableting machine
Production reached 1.5 million / h. Its production is much higher than domestic production of tablet presses, tablet confidential domestic production to catch up in terms of speed than abroad, you need to create a tabletting machine design
New processing technology, automatic control and other aspects have made great progress. Tabletting machine
(2) tabletting process link airtight and flow, logistics isolation. Foreign tableting machine input and output is very good sealing, to minimize cross-contamination
. Granules for tableting barrel and closed via a closed conveyor system into the hopper, tabletting process to take effective measures to prevent dust emissions and particulate stratification, pressure is good
Tablets through sieve, the film detection, metal detection, etc. into the packaging process, the whole process was very confined. While most domestic pressure tableting machine process is open,
Or is not completely closed, fracture resulting tableting process between dust. With the further implementation of GMP in the tabletting process link airtight and flow, logistics
Isolation becomes particularly important, this is our design and manufacture equipment must have the basic functions.
(3) CIP. CIP (cleaning in place) tableting machine, enabling users to significantly reduce the cost of equipment. Improve the tableting machine cleaning function, in addition to the design
Fully consider the various parts of the cleaning, the tableting machine disassembly cleaning function is to emphasize that only convenient and quick removal, in order to ensure the thoroughness of cleaning.
(4) 21CFRPart11 (electronic records and electronic signatures) in tableting machine application. August 20, 1997, FDA issued 21CFR11 Part 6 "e-
Records, dental Suction Unit electronic signatures (ER / ES) with the relevant regulations came into force. Of electronic signatures and electronic records, the present regulations are enforced, the purpose of this Ordinance
Of that for pharmaceutical products and food processing to facilitate the introduction of electronic technology. It can provide a suitable and practical guidelines, as set forth
What to do in the past through the electronic form in writing task. Refers to the electronic record as text, graphics, data, audio, icon, or other by scoring
Computer systems to create, modify, maintain, archive, collect or distribute information in digital form between the expression of any combination. Electronic signature refers performed by individuals
, Adopted or authorized, and after a computer data compilation of any symbol or series, which conform with personal handwritten signature has the same legal effect.
21CFRPart11 technology in the tablet press on the application, making the tableting machine with device diagnostics logging, logging accidents and alert notification log. These electronic records
And electronic signatures are detailed records on a variety of operational data, accident data. Compliance with safety access control, requires a user name and password to enter the operation. All numbers
According to the use of the electronic signature function, including the operator name, date, time, serial number, problems, solutions, condition data. All raw data are not
Can be artificially modified to ensure the reliability and authenticity. The presence of these systems and users will automatically log into the whole "traces review" folder. This
Some security attribute data format "to ensure data changes are under the control of the overall examination into the tablet press line. Domestic in this area is just beginning.
(5) connected with the entire production line control technology. Put a tableting machine can be connected to a production line in Germany and the UK tableting machine have this feature
. It has a beginning, end, and speed adjustment function. Use this option to function reliably, automatic production line with other devices, such as sieve, suction
Dust, testing, transportation, bottled, etc. are connected together, synchronization is complete pills suppress production tasks. Meanwhile, the external device also uses a different means of monitoring,
Provides high security and reliability of energy. Using the line detector can suppress tablets clear burrs, remove dust; vacuum monitoring function is the use of traffic
Monitor regularly the specified location on the suction tube suction pressure testing. Continuously set and actual values of the comparison, if the detector 10s in the suction tube
The suction pressure is not detected (no flow), the pressure plate machine that is a fault alarm and stop operation. This feature is to maximize the protection of the production can be
Reliability, the tablet can be continuously remove the dust suppression of the production process. And the entire production line to connect the tablet is a tablet control technology production control of new technologies, is the future
Trends. This technology in China has just started.
(6) tableting machine remote monitoring and remote diagnostic system. With networking, broadband network, virtual, etc. The rapid development of high-tech computer equipment remote monitoring and
Remote diagnostics technology is also increasingly emerging. Computer-controlled pharmaceutical tableting machine began extensive application of remote monitoring and remote diagnostics technology in the industry has a tableting machine
Useless. , Advanced in developed countries has generally been on the tableting machine with remote monitoring and remote diagnostics. In order to establish such a system is also implemented technical support
Center (service side) and tableting machine side (user) dialogue through the Internet network, enabling service side can understand the user via the Internet in different places tableting machine out
The fault lies now, and tabletting machine working status of the instruction is executed, and then on the tableting machine fault judgment and propose possible solutions. By a tabletting machine
Remote monitoring and remote diagnostics system establishment, real-time troubleshooting, greatly improving the tableting machine manufacturer's service response capacity and speed, but also
Improve the economic efficiency of enterprises. Tabletting machine remote monitoring and remote diagnostics system should include staffing, network construction, hardware and software selection, etc.,
Respectively, to complete failure of the monitoring, analysis, feedback, and real-time resolution services issued these processes in order to ensure the effective operation of the entire system.
the control points
⑴ control orifice positioning error
In the above settings Secant Pile Top Construction guide wall (This project uses reinforced concrete guide wall, can also be recycled steel guide wall), the guide wall set positioning hole, the diameter should be bigger than the pile diameter 20 ~ 40mm. Rig in place, check the first one cannula inserted into the positioning hole and require the construction unit is adjusted so that the positioning around the casing to maintain a uniform gap between the holes.
⑵ urge the construction unit controls the vertical piles
According to design requirements, dental instruments pile vertical deviation of not more than 3 ‰. Secant pile in order to ensure a sufficient thickness at the bottom of the amount of bite, in addition to its strict control orifice positioning errors, but also its vertical strictly controlled.
Pore-forming process to control the verticality of the pile, you must grasp the following three aspects of the work:
① straight cannula degree examination and correction
Secant piles on flat ground before casing straight degree examination and correction, first check and correct single casing straight degrees, and then will follow the entire length of the pile sleeve configured to connect together for the entire root sheath tube (15 ~ 25m) of straight deviation should be less than 10mm. Detection method: measured on the ground emit two mutually parallel lines, the sleeve is placed between the two lines, and a line for testing the hammer and ruler.
② pile into the hole during the vertical monitoring and inspection
a ground monitoring: ground select two mutually perpendicular directions using the line hammer monitoring above-ground parts of the vertical casing, correct any deviations found. This test in each pile into the hole process should adhere to from beginning to end, can not be interrupted.
b check: After installing each section of casing pressure casing before the next section, we must stop to use the "test loop" in the hole verticality checks, failed when the need for correction, until qualified to the next section casing construction.
③ correction
Pore-forming process, such as found in vertical deviation is too large, the importance of timely corrective adjustments require the construction unit, correcting There are three common methods:
a cylinder with a rig for correction: If the deviation is not greater than or buried casing is not deep (5m less), you can directly use the rig two jacking cylinders and two sliding vertical cylinder adjustment sleeve, you can achieve the purpose of correcting .
b pile Correction: If A pile buried 5m large offset occurs below, you can first use drill cylinder direct correction, such as below standard, can be filled with sand to the casing or clay, while filling side uprooted casing, until enhance the sleeve to the last pass the inspection place, and then straighten casing, check and re-qualified under vertical pressure.
c correction: B Pile A pile corrective method is basically the same, the difference is that the casing can not be filled while filling the same with the A pile of concrete, or they may be left in the soil between piles mezzanine, thus affecting the row Pile waterproof effect.
⑶ ultra-retarding Concrete Construction Quality Control
A pile of concrete retarding time should be based on time to determine the pile into the pile, pile into the pile time and geological conditions of the construction site, pile length, pile diameter and drilling capacity factors. According to bite Piles, A pile initial setting time of T = 3t + K + Q;
Where: T - A pile of dental hand piece concrete retarding time t - the time required for single pile into the pile
K - reserve time, usually 1.0t Q - Night downtime
A pile general preliminary control initial setting time of 60h, the construction in the future be adjusted according to the scene.
⑷ occlusal thickness determination
Engagement between adjacent pile thickness d to select based on length of pile, pile shorter occlusal thickness is smaller, thicker pile longer bite, are calculated as follows:
2 (kl + q) ≤ d - 50mm (which is to ensure a minimum pile occlusal thickness not less than 50mm)
Where: l - pile length d - Secant Pile design occlusal thickness
k - pile verticality q - orifice positioning error tolerance
2013年9月3日星期二
Three Mistakes of cleaning teeth
Myth one: daily brushing, teeth cleaning can be described as superfluous
In developed countries, has become very popular teeth cleaning routine dental care, people generally once or twice a year to find their dentist regularly to clean teeth. Therefore, we are now the most important is a correct understanding of cleaning teeth, changing concepts. Cleaning teeth cleaning teeth completely different from ordinary light surface dirt, it can not be completely removed by ordinary brushing to remove plaque, calculus, and deposited on the tooth surface of the pigment, thereby enabling organizations to maintain periodontal health, prevention and treatment of periodontal disease; and easy to find when cleaning teeth tiny imperceptible dental problems, such as the relatively hidden caries, to achieve the purpose of early detection and early treatment. Under normal circumstances, teeth cleaning as a routine care in six months or a year wash, for patients with Light Cure periodontitis, you need the guidance of a doctor for regular teeth cleaning.
Myth: cleaning teeth can damage teeth, worn tooth enamel surface
A lot of people kind of concerns, cleaning teeth will wear away the enamel surface of the tooth. In actual fact, ultrasonic scaler, it is the principle of ultrasonic vibration, not worn out, no harm to the teeth, the needle does not have any cutting function, is to rely on high-frequency ultrasonic vibrations to break calculus, but also in cleaning teeth after By polishing, sandblasting in the teeth externally applied layer of protective film, slowing the speed of the stone again.
Myth: beauty salon and a few small clinics have clean teeth, there faster than a regular hospital, more convenient
Now if there is a dental clinic, hospital, generally have clean teeth this service, even the little salons also have such service, and very cheap. But the doctors spoke of the need to promote clean teeth, but also to secure formal. In some small clinics or beauty salon, and its rapid irregular teeth cleaning teeth cleaning methods will give those who have adverse consequences for cleaning teeth's enamel damage itself, forming the naked eye can not see the surface scratches, dental supply companies but also damage to the gums, increased periodontal disease, the most serious yet easily cause cross-infection, without safe disinfection of instruments is very easily transmitted viruses such as hepatitis and AIDS, to give people cause trouble. In the regular hospital by medical personnel are dedicated to the operation, the most commonly used is the ultrasonic scaler, the instrument, the needle should be strictly disinfected.
cleaning teeth
Cleaning teeth is a good means of dental care is also the primary treatment of periodontal disease measures, through regular cleaning teeth, not only can thoroughly remove plaque and calculus on the teeth, so to maintain a healthy periodontal tissues, prevention of periodontal disease, moreover, easy to find when cleaning teeth tiny imperceptible dental problems, such as the relatively hidden caries, so as to achieve the purpose of early detection and early treatment.
Cleaning teeth, commonly known as scaling, jargon supragingival scaling technique (supragingival scaling), refers to the equipment used to remove supragingival scaling tartar, plaque and color stains and polish the tooth surface, to delay the re-deposition of plaque and calculus . Plaque and tartar are the most important local incentives periodontal disease, surgery is the removal of subgingival scaling plaque and tartar on the most effective method.
Teeth cleaning - Methods
Hospital cleaning teeth
Hospital cleaning acrylic resin teeth can be divided into ultrasonic scaler, sandblasted clean teeth, clean teeth and hand-three. Now we often say that the teeth cleaning generally refers to the ultrasonic scaler and sandblasting cleaning teeth, teeth cleaning method for these two indications are not the same.
Living Scaler
Called life cleaning teeth, in the daily life of the most commonly used method of cleaning teeth. The most commonly used to maintain oral health and necessary way to clean teeth brushing, in addition, mouthwash, toothpicks, etc. are also common teeth cleaning methods.
2013年9月2日星期一
missing teeth bite
Generally missing teeth bite mainly refers to the remaining maxillary dental midline midline is not aligned with the teeth, jaw teeth down side to the inside, which not only affects the appearance of the teeth, but also for the normal functioning of oral and periodontal health and Oral health has a great impact. By U.S. dental correction to achieve good results. Reason
(1) early loss of teeth: there will be lack of space, resulting in crowded dislocation.
(2) bad habits: habitual thumb sucking, licking tongue. Jiao lips, bite things, stretching the lower jaw and the bad habit of swallowing, unilateral chewing habits, etc., can cause a variety of malocclusion.
(3) more teeth: teeth can cause multiple teeth, jaw morphology system dysfunction.
(4) Congenital dental Suction Unit missing teeth: more development and embryo reasons, mostly for lack of third molars phylogenetic degradation.
(5) deciduous teeth: Individual Dental shedding of deciduous teeth are not overdue, for following the eruption of permanent teeth can lead to the obstruction was an ambush, or misplaced eruption.
(6) Rujian tooth wear inadequate: because children eat too soft, so some nipples more teeth than other tooth wear, and thus higher arch occlusal surface, resulting in premature contact, causing the front or side movement, the formation of crossbite.
Missing teeth bite correction method can be used to solve, but very safe, according to each person's situation to determine the correction techniques and methods, it is best to a regular hospital for consultation.
no brackets invisible braces
Missing teeth bite can be used without brackets invisible corrective surgery to repair without brackets invisible surgery allows patients in the beautiful and comfortable succeed in straightening teeth. No brackets invisible braces are innovative stereoscopic 3D computer technology, tailored to a range of nearly imperceptible transparent denture to complete the entire orthodontic treatment. No invisible orthodontic bracket orthodontic parts that require applying a corresponding pressure on the site of deformity under pressure in a long time slowly move to the correct position. Various malformations, different expected results, dental unit price correct the installation to be used in different ways. Whether due to crowded teeth, there is a gap, or displaced teeth after conventional treatment, absolutely can regain smile. [1]
No bracket has two straightening teeth surgery advantages:
1, convenient: dental panoramic head measuring instrument accurately measured and calculated data misplaced teeth, one-time modeling, invisible braces can bring their own use at home, eliminating the pain of frequent referral.
2, invisible braces: braces are transparent, direct stuck deformity teeth, misaligned teeth quietly changed.
订阅:
博文 (Atom)